パイプカッターの使い方 How to use pipe cutter
- 2017/09/10
- 23:49
パイプカッターの使い方 How to use pipe cutter
こんにちはRoboTakaoです。ようこそ「極力ローコスト ロボット製作 ブログ」にお越しくださいました。
Hello everyone! I'm Robo Takao. Welcome to "low cost robot building blog"!
今回は私の使っている道具達の中からパイプカッターとその使い方を紹介します。
I introduce my pipe cutter.

私の場合、ロボットの関節などにパイプを使用しています。そのパイプはダイソーで買ってきたパイプカッターでカットしています。
In my case, I use a pipe for robot joints etc. The pipe is cut with a pipe cutter that I bought at Daiso.
使い方 How to use
1)ノギスで測りながらカットする位置を決め、ハンドルを回して固定する。
この時、あまり締めすぎるとパイプカッターを回せなくなるので気を付けて締めます。
ノギスで測った場合に、カッターの厚みのために少しずれます。調整しながら測りましょう。
Determine the position to cut while measuring with a vernier caliper,
fix it by turning the handle. At this time, if you tighten too much,
you will not be able to turn the pipe cutter, so be careful and tighten.
When measuring with a vernier caliper, it is a little off due to the thickness of the cutter.
Please measure it while adjusting.


2)パイプカッターを回します。最初は固いですが、徐々に回るようになります。
Turn the pipe cutter. At first it is hard, but it will gradually turn.

3)またハンドルで締め上げます。この繰り返しです。
Also tighten with a handle. Repeat these steps.

切れました。
それでは今回はこの辺で失礼します!ありがとうございました。
Thank you for your visiting!
こんにちはRoboTakaoです。ようこそ「極力ローコスト ロボット製作 ブログ」にお越しくださいました。
Hello everyone! I'm Robo Takao. Welcome to "low cost robot building blog"!
今回は私の使っている道具達の中からパイプカッターとその使い方を紹介します。
I introduce my pipe cutter.

私の場合、ロボットの関節などにパイプを使用しています。そのパイプはダイソーで買ってきたパイプカッターでカットしています。
In my case, I use a pipe for robot joints etc. The pipe is cut with a pipe cutter that I bought at Daiso.
使い方 How to use
1)ノギスで測りながらカットする位置を決め、ハンドルを回して固定する。
この時、あまり締めすぎるとパイプカッターを回せなくなるので気を付けて締めます。
ノギスで測った場合に、カッターの厚みのために少しずれます。調整しながら測りましょう。
Determine the position to cut while measuring with a vernier caliper,
fix it by turning the handle. At this time, if you tighten too much,
you will not be able to turn the pipe cutter, so be careful and tighten.
When measuring with a vernier caliper, it is a little off due to the thickness of the cutter.
Please measure it while adjusting.


2)パイプカッターを回します。最初は固いですが、徐々に回るようになります。
Turn the pipe cutter. At first it is hard, but it will gradually turn.

3)またハンドルで締め上げます。この繰り返しです。
Also tighten with a handle. Repeat these steps.

切れました。
それでは今回はこの辺で失礼します!ありがとうございました。
Thank you for your visiting!
スポンサードリンク